How To Set Up A Reese Equalizer Hitch

Weight Distribution Hitch Setup

How to Set Up a Weight Distribution Hitch - CURT

Weight Distribution Hitch Setup

8 Easy-to-Follow Steps!

Weight distribution hitch installation involves leveling the trailer, measuring vehicle and trailer height, mounting the hitch head, shank, bound bars and hookup brackets, and adjusting the weight distribution hitch as needed.

In this guide, nosotros will cover step by stride how to prepare a weight distribution hitch. Each hitch is unique, then make certain yous follow the instructions included with your particular model.

Weight Distribution Hitch Installation Video

How to Install and Adjust Your Weight Distribution Hitch

Step one: Measure vehicle and trailer height

Park your vehicle and trailer on a level surface and employ the trailer tongue jack and a level to make certain your trailer is parallel with the ground.

Measure and record the superlative of your vehicle and trailer. You lot will demand to know the distance from the basis to the height of the trailer coupler and the distances from the footing to the bottom of the rear bumper and front bumper on your tow vehicle. You can also use the distance from the ground to wheel well if you adopt.

Stride ii: Attach the WD shank and hitch caput

Insert the weight distribution shank into the receiver tube. Be sure that the shank is fully inserted in the receiver tube of your trailer hitch and secure it using a hitch pin & clip.

Position the caput associates on the adjustable shank. The head should exist raised into position then that the top of the trailer ball is i to three inches in a higher place the coupler height. Apply one mounting bolt at the bottom of the assembly to hold it in place, but do not tighten with a nut.

Need more drib or rise? Shop replacement shanks

Step 3: Set up weight distribution hitch caput angle

Pivoting the caput downward, identify 2 washers on the adjustment rod and insert the rod into the lower pigsty on the head. Some weight distribution hitches may non require this pace, having a different adjustment mechanism. Call back to consult the instructions specific to your weight distribution hitch.

Rotate the head up into the mounting position on the shank. It should exist vertical or tilted slightly back. You may need to add or remove washers to achieve the proper angle.

Finally, insert the second bolt into the top hole in the hitch head and fasten both bolts with the provided nuts and washers. Tighten the bolts but merely enough to hold the head in place.

Step iv: Install spring bars and couple the trailer

Mount the spring confined on the hitch caput. If the spring bar chains have not notwithstanding been fastened, adhere them to the spring bars earlier mounting the bars to the head.

Raise the trailer coupler, and back the tow vehicle up to couple the trailer to the trailer ball.

Step 5: Raise the trailer jack

With the coupler latched onto the trailer ball, lift upwards the coupling point using the trailer jack. The coupler should be raised about 3 inches above the level position.

Step half dozen: Engage the hookup brackets

Position the jump bar hookup brackets on the trailer frame using the spring bar bondage as a guide. Mount the brackets onto the trailer frame using the provided bolts.

So, attach the leap bar chains to the brackets. Brand sure both sides are spaced the same vertically, with number of chain links betwixt the bound bars and the hookup brackets. And so pry the brackets into the locked position using the provided lift handle.

Note: There must exist a minimum of five concatenation links betwixt the bracket and the leap bar.

Footstep 7: How to adjust weight distribution hitch

Retract the trailer jack so that the full weight of the trailer is resting on the hitch. Then, re-measure out the distances between the ground and the forepart and rear bumpers. Each distance should exist within 1/2" of the original measurement. If the distances have changed as well drastically, you can conform the number of links on the spring bar chains to increase or decrease tension. Yous can also suit the tilt of the head unit.

Stride 8: Fully tighten the bolts

Uncouple the trailer and torque all hardware to the values specified in the instructions.

Weight distribution setup differs across various models. With your weight distribution hitch, e'er follow the instructions provided by the manufacturer, and recollect to have your time.

Weight distribution and sway control in one production!

The TruTrack™ weight distribution hitch features an innovative design that levels the vehicle-trailer combination, while actively keeping the trailer from swaying.

No need for a divide sway control unit!

Back to Weight Distribution Hitches